Congratulations on becoming the proud owner of an Airboard PRO. Before you tear up the streets please take the time to read these instructions as it will help to stop you and your Airboard PRO shredding big time and keep you looking cool !!!
Firstly, please check you have received what you ordered, if not please contact us at: [email protected]
Always place your feet in the middle of the foot pads when riding!
This is the correct riding position and will help you when learning to master riding your Airboard PRO!
Feet facing forward and the same distance from the wheel arch….
Ok, so that’s the boring stuff out of the way, now lets get started: after switching on the Airboard PRO. Have your bluetooth device ready, let’s say you are trying to connect the bluetooth on your phone to the Airboard PRO. Check your phone has bluetooth switched on. Use your phone to search for new devices and the Airboard PRO should appear as code “WHEEL MUSIC” or similar. Once it has recognised and connected the Airboard PRO will audibly confirm connection has been made…. Simples!! Now just select the music you want to listen to and boom!! You can blast out your tunes, your volume is controlled from your bluetooth device, so make sure your volume is up when you play your tunes through your Airboard PRO.
So you’re now ready to get moving. Get on one foot at a time from behind the Airboard PRO and always get off the rear one foot at a time. First of all use the Airboard PRO using just one foot i.e. one foot on Airboard PRO one on the ground; just to feel the movement of the Airboard PRO. Tip foot forward and feel the Airboard PRO move forward. Tip foot backwards and feel the Airboard PRO move backwards. Master the Airboard PRO moving back and forth before trying both feet. The Airboard PRO is incredibly sensitive, slight movements are all that is needed for the board to react.
First time on an Airboard PRO?
OK, hold on to something i.e. to a person or a fixed object like a kitchen work surface. Once on with both feet stand still and allow Airboard PRO to balance before you move. The secret to your success is to make sure you can stand still in the horizontal position on the Airboard PRO.
Now lean slightly forward and press lightly on the front of the pedals and you will start to move forward. Drop your heels and therefore the opposite applies and you will move backwards. Just try to move forwards and backwards while holding on.
To rotate the Airboard PRO press one pedal forwards and one backwards, whilst taking care to stay balanced on the Airboard PRO. Try moving forwards slowly now. Keep holding on to someone’s hand till your confidence grows. With a bit of patience and practice you will master it in no time. Most people can start moving with confidence in under an hour, some people pick it up in just 5 minutes.
Your Hoverboard Swegway Battery
The battery in the Airboard PRO is a 20 cell battery pack and is of the highest possible quality verfied and certified safe available at the time of manufacture. When new it may take up to twenty re-charge cycles for it to reach its full capacity. It is recommended to use and recharge battery fully and draining fully each time.
DO NOT leave charging overnight.
Charge time is 2 hours.
When in Balance Mode, if the Airboard PRO moves forwards or backwards on its own on flat ground, or feels more responsive on one side than the other, from time to time it will need to be recalibrated.
To Calibrate the Airboard PRO
Confirm that the Airboard PRO is off and on a flat surface, making sure that the footpads are in a 100% horizontal flat position. Make sure the Airboard PRO is turned off, press and hold the power switch for 5 seconds and then release it. When you hear a sound, the system starts to calibrate; the red light (that is, the running indicator and the left turn indicator) flashes 3 times. Wait for 60 seconds, the system calibration is now configured. Turn it off and on again and your Airboard PRO will be reset to the correct horizontal balanced start position.
Self-Balance Mode
Place the Airboard PRO horizontally and make sure it is turned on, press the power switch for about 6 seconds, until you hear the beep, then restart the Airboard PRO. The adjustment is complete. You can easily set this mode through the GYROOR APP.
Child Mode / Adult Mode
Stand the Airboard PRO up on its side. Press the power button to turn it on – release the button – then keep it pressed for about 6 seconds until the beep is heard and the Airboard PRO is restarted. Perform the same action to switch back to original mode. You can easily set this mode through the GYROOR APP.
Alarms
Overheating can occur when riding for an extended period of time, which could increase the internal temperature of your Airboard PRO in excess of 122°F(50º C). If this happens, the glow lights will flash red, an alarm will sound and your Airboard PRO will not be able to charge. Simply step off the Airboard PRO, power it off, and give it time to cool back down to a normal operating temperature.
Other alarms
For any other alarms, try restarting your Airboard PRO. If the problem persists, please contact our after-sales service.
Battery
High Powered (Cells) 20 Series
36V DC 4000mAh 144WH
Battery Management System
Over-voltage, under-voltage, short circuit, and over-heating protection. Auto-sleep and auto-wake.
Power Required
AC 100-240v / 50-60Hz
ONLY USE CHARGER “HLT-180-4201500“
Charging Voltage
42V DC
Speed
10 – 20 kmh (Depending on rider and buggy attachment)
Range
10 – 20 km (Depending on rider and buggy attachment)
Motors
2 x Brushless 250w Infinity Wheels
Charge Time
First Charge is 3 hours. Use Airboard PRO.
Then 2 hours each time thereafter.
Maximum Load
150 kg
Minimum Load
22.5 kg
Max Gradient Ability
16º
Warranty
12 months on battery, charger & charging port
Net Weight
10 kg
Gross Weight
11 kg
Ground Clearance
40 mm
Platform Height
125 mm
Speed Safety Protection
Child mode, tilts level when reaches set speed
Storage Conditions
-20ºC to 50ºC
Usage Temperature
-10ºC to 40ºC
Waterproof and
dustproof level
IP54
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Please read our Do’s and Don’ts pages. Small children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Airboard PRO boards are ONLY to be used with the power supply unit provided – “HLT-180-4201500“.
Airboard PRO boards must only be used at the extra low voltage corresponding to the marking on the product. DO NOT USE A THIRD PARTY POWER SUPPLY.
After first charge of 3 hours, and first use, do not charge for more than 2 hours each time thereafter, doing so could harm your battery performance.
CE Marking on a product is a manufacturer’s declaration that the product complies with the essential requirements of the relevant European health, safety and environmental protection legislation, in practice by many of the so-called Product Directives.*
*Product Directives contains the ™essential requirements∫ and/or ™performance levels∫ and ™Harmonized Standards∫ to which the products must conform. Harmonized Standards are the technical specifications (European Standards or Harmonization Documents) which are established by several European standards agencies (CEN, CENELEC, etc). CEN stands for European Committee for Standardization. CENELEC stands for European Committee for Electrotechnical Standardization.
The WEEE Directive (Waste from Electrical and Electronic Equipment Directive) 2002/96/EC uses a special logo in addition to the CE logo to show that the equipment should not be disposed of in the normal waste stream.
The purpose of the WEEE Directive is, as a first priority, the prevention of waste electrical and electronic equipment (WEEE), and in addition, the reuse, recycling and other forms of recovery of such wastes so as to reduce the disposal of waste. It also seeks to improve the environmental performance of all operators involved in the life cycle of electrical and electronic equipment, e.g. producers, distributors and consumers and in particular those operators directly involved in the treatment of waste electrical and electronic equipment.
